Наукові конференції України, Інновації молоді в машинобудуванні 2024

Розмір шрифту: 
Оброблюваність деталей виготовлених адитивними технологіями
О. В. Сонець, Б. С. Воронцов

Остання редакція: 2024-04-22

Анотація


Через зростаючу популярність технологій адитивного виробництва в сучасному машинобудуванні, очевидним є той факт, що необхідно вивчати і систематизувати методи і можливості їх впровадження в технологічний процес. У цій роботи вивчається одна з проблем 3-D друку, що впливає на оброблюваність надрукованих деталей. Також визначається поле і напрямки можливих досліджень цієї проблеми.

Ключові слова


адитивні технології; механічна обробка; анізотропія мікроструктури

Посилання


1. E. Liverani, S. Toschi, L. Ceschini, A. Fortunato. (2017) Effect of selective laser melting (SLM) process parameters on microstructure and mechanical properties of 316L austenitic stainless steel. https://doi.org/10.1016/j.jmatprotec.2017.05.042

2. Amato, K. N., Gaytan, S. M., Murr, L. E., Martinez, E., Shindo, P. W., Hernandez, J., ... & Medina, F. J. A. M. (2012). Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting. Acta Materialia, 60(5), 2229-2239. https://doi.org/10.1016/j.actamat.2011.12.032

3. L. Thijs, M.L. Montero Sistiaga, R. Wauthle, Q. Xie, J.P. Kruth, J. Van Humbeeck. (2013) Strong morphological and crystallographic texture and resulting yield strength anisotropy in selective laser melted tantalum. https://doi.org/10.1016/j.actamat.2013.04.036

4. E. Segebade, M. Gerstenmeyer, S. Dietrich, F. Zanger, V. Schulze. (2019) Influence of anisotropy of additively manufactured AlSi10Mg parts on chip formation during orthogonal cutting. https://doi.org/10.1016/j.procir.2019.04.043

5. Fernandez-Zelaia, P., Nguyen, V., & Zhang, H. (2019). The effects of material anisotropy on secondary processing of additively manufactured CoCrMo. Addit Manuf, 29: 100764. https://doi.org/10.1016/j.addma.2019.06.015

6. Hojati, F., Daneshi, A., Soltani, B., Azarhoushang, B., & Biermann, D. (2020). Study on machinability of additively manufactured and conventional titanium alloys in micro-milling process. Precision Engineering, 62, 1-9. https://doi.org/10.1016/j.precisioneng.2019.11.002

7. Simonelli, M., Tse, Y. Y., & Tuck, C. (2014). Effect of the build orientation on the mechanical properties and fracture modes of SLM Ti–6Al–4V. Materials Science and Engineering: A, 616, 1-11. https://doi.org/10.1016/j.msea.2014.07.086

8. Carroll, B. E., Palmer, T. A., & Beese, A. M. (2015). Anisotropic tensile behavior of Ti–6Al–4V components fabricated with directed energy deposition additive manufacturing. Acta Materialia, 87, 309-320. https://doi.org/10.1016/j.actamat.2014.12.054

9. Lizzul, L., Sorgato, M., Bertolini, R., Ghiotti, A., & Bruschi, S. (2020). Influence of additive manufacturing-induced anisotropy on tool wear in end milling of Ti6Al4V. Tribology International, 146, 106200. https://doi.org/10.1016/j.triboint.2020.106200

10. Lizzul, L., Bertolini, R., Ghiotti, A., & Bruschi, S. (2020). Effect of AM-induced anisotropy on the surface integrity of laser powder bed fused Ti6Al4V machined parts. Procedia Manufacturing, 47, 505-510. https://doi.org/10.1016/j.promfg.2020.04.149


Full Text: PDF